The article has been added successfully.
98 more products in this category
Racingbros Modi low friction Scraper Set 32mm (FOX - RockShox - X Fusion)
More performance at a better price.
Features
- Hybrid mixture: The peculiarity of this scraper is on the addition of MoS2, graphite and PTFE in the Lycran material. This enables a very low breakaway torque is achieved, which improves the response of the fork.
- One-piece construction: The one-piece wiper performance modes of Racingbros unite dust seal and oil seal in one component. This they hold, as compared to conventional two-piece seals where a higher system pressure of up to 20 kg / cm. The oil inside the fork is held reliably be kept away from the inside of the fork in the system while dirt, mud or sand.
- Long shelf life: both in long-term test of 20,000 suspensions under spraying mud, sand, water and ice as well as Numerous test pilots during the development phase, the high quality has shown:
- completely waterproof and UV-resistant
- Working Temperature of -25 ° -80 ° Celsius
- Best Value for money: Compared to the aftermarket fork seals manufacturer cheaper.
These seals are suitable for the following models with 32mm fork stanchions:
- FOX 32
- FOX 32 VAN
- FOX 32 VANILLA RL
- FOX 32 VAN VANILLA RLC
- FOX 32 Float
- FOX 32 Float CTD
- FOX 32 Float 29
- FOX 32 Float RL
- FOX 32 Float RLC
- FOX 32 Talas
- FOX 32 Talas RL
- FOX 32 Talas CTD
- FOX 32 Talas 180
- Rock Shox Boxxer 2006-2009
- Rock Shox Revelation
- Rock Shox Revelation rl
- Rock Shox Revelation rlt
- Rock Shox Sektor
- Rock Shox Reba
- Rock Shox Pike
- X-Fusion Velvet
- X-Fusion Velvet RL
- X-Fusion Velour
- X-Fusion Velour RL
- Specialized AFR
Scope of delivery
- 1 x Wiper Set 32 mm
R1510001
806891001436
806891001436
Evaluations
5 Stars 2 (2)
4 Stars _ (0)
3 Stars _ (0)
2 Stars _ (0)
1 Stars _ (0)
To submit a rating, please log in.
We do not check whether the rated item was purchased from us.
Last viewed
They are holding super good, no oil waste and it is really low friction.
Sehr gute Dichtringe.... haben an meiner Fox 32 F80 RL Remote F-Series aus 2009 gut gepasst. Einzig die letzten paar Millimeter gingen sehr sehr schwer einzutreiben, ich wollte das Casting aber auch nicht mit den Ausfallenden auf den Boden stellen und habe sie daher nur auf dem Schoss gehabt was natürlich sehr federt. Die letzten paar Millimeter waren nur mit dem Hammer und Einpresswerkzeug einzutreiben. Das Einpresswerkzeug hatte ich aus dem 3D Drucker und hat ganz schön gelitten dabei, aber hauptsache die Ringe sitzen. Im Gegensatz zu den Originalen Dichtrungen von Fox sind sie aber wohl doch einiges besser da sie eben die Flange besitzen welche Fox ab 2016 weggelassen hat. Somit besteht nicht die Gefahr die Dichtringe zu tief einzutreiben. Beachten sollte man das die Dichtringe 42mm Außendurchmesser haben, und es aber Gabeln gibt die nur 41mm Innendurchmesser bei den Aufnahmen im Casting haben. Das wären zwar "nur" 0,5mm auf jeder Seite und man könnte meinen es ist ja nur Gummi und das drückt sich schon... bekommt man aber auf keinen Fall passend rein, da die Ringe selbst außen knüppelhart und Metal verstärkt sind. Ist mir ehrlich gesagt auch ein Rätsel warum die letzen Millimeter so schwer gingen aber naja drin ist drin und keine Macken am frisch lackiertem Casting XD.