- In magazzino, tempo di consegna 1-3 giorni
inclusa 19% IVA, più 4,49 € di spese di spedizione
Radon equipaggia la tua officina per biciclette
I ciclisti più assidui a volte devono sostituire il movimento centrale. Il cuscinetto del movimento centrale ha l'importante compito di guidare l'albero del movimento centrale. Un movimento centrale è sempre composto da almeno due cuscinetti che sostengono l'albero su entrambi i lati della scatola del movimento centrale. Radon offre strumenti affidabili anche in questo settore speciale, soprattutto per i movimenti centrali Press-Fit, ma anche per altri standard.
Caratteristiche - Set di utensili di montaggio e smontaggio Pro Press-Fit
- Per il montaggio di gusci di cuscinetti o staffe inferiori Press-Fit
Caratteristiche del prodotto
- Per il diametro dell'asse: 24 mm
- Lunghezza: 240 mm
- Diametro: 21 mm
Compatibilità
- Shimano Pressfit
- Per il montaggio di gusci di cuscinetti o di movimenti centrali Press Fit (Press-Fit BB, BB30 e cuscinetti da 24 mm)
- Adatto per i tipi di cuscinetti BB30, BB86/92 e BB90
Materiale
- Acciaio per utensili
Peso
- circa 242 g
Ambito di consegna
- 1 x Attrezzo di montaggio Pro per movimento centrale Press-Fit
- 1 x attrezzo di smontaggio Pro per movimento centrale Press-Fit
Radon Pro: attrezzatura professionale per l'officina
Gli strumenti della serie Pro sono stati progettati per i meccanici di biciclette più esigenti. Gli utensili speciali devono soddisfare requisiti particolari nell'uso regolare e multiplo nell'officina di biciclette. Materie prime di alta qualità, tecniche di produzione precise con tolleranze ridotte e un attento controllo della qualità fanno degli utensili Radon Pro degli affidabili aiutanti per la bicicletta. Si distinguono per l'affidabilità, la robustezza e la durata.
4059454033061
It does the job. The press tool is excellent but a bearing-cup extraction-stick is made from weak material. It is too expensive for what it is.
Works as expected
nickel merci BD
Super Set. Damit klappt die Reparatur ohne Probleme. Kann ich jedem nur empfehlen! Das Einpresswerkzeug macht wirklich Sinn, da es die Lagerschalen sauber führt und Verkanten ausschließt. Ich wollte zuerst ein selbst gebasteltes Tool verwenden, bereue den Kauf aber genau deshalb nicht.
The press works well, just that 1 side was not pressed in fully and the other was. However it was 100% straight so I just gave the drive side BB a few punches with the side of my plastic hammer and the 1-3mm of space where gone. Always look at both sides when doing this, to much torque can destroy the frame. The removal tool does it's job, I think it's useful to do 1 side with the tool and the other with a large flat screw driver and hammer because it's difficult to position the tool when 1 side it gone. They should add a ring you can put on there so when 1side is gone the tool still stays straight and you can hammer out the other side.
Mit dem Werkzeugset sollte ein Shimano SM-BB72-41B getauscht werden. Die 4 Zungen des Demontagewerkzeugs werden durch die Innenhülse soweit zusammengedrückt, dass die Enden nicht mehr sauber in die Lagerschale greifen. Ein geordnetes Austreiben der Lagerschalen ist so nicht möglich. Abhilfe schafft ein leichtes nach außen knicken der Zungenenden (ähnlich Parktool BBT-90.3). Die Ausführung der Druckscheiben beim Montagewerkzeug würde zu einer Einleitung der Presskräfte auf die Kunstoffhülse und im weiteren auf den Lagerinnenring führen. m.M nach kann dies zu einer Vorschädigung des Lagers führen. Abhilfe schufen zusätzliche Adapterscheiben die den Druck auf die Lagergehäuse einleiten. Fazit: Mit etwas Bastelei ein durchaus verwendbares Werkzeug. Wer dies scheut, sollte für Shimano Pressfit ein anderes Werkzeug wählen
Das Demontage-Werkzeug ist unbrauchbar, springt beim Ausschlagen des Press-Fit Innenlagers einfach über. Das Montage-Werkzeug hat dagegen einwandfrei funktioniert. Montage-Werkzeug: 5 Sterne, Demontage-Werkzeug: eigentlich 0 Sterne.
Hallo, hab heute das pressfit Demontage und Montage Werkzeug bekommen und gleich verwendet. Rechte Lagerschale war sehr fest und das Kugellager wurde von der Kunststoffschale beim Austreiben getrennt. Der Kunststoffkonus ließ sich dann leicht mit einem Holz austreiben. Die Einpressung des neuen Innenlagers funktionierte dann sehr gut.
It does the job. The press tool is excellent but a bearing-cup extraction-stick is made from weak material. It is too expensive for what it is.
Works as expected
nickel merci BD