Radon equips your bike workshop
Frequent riders sometimes can not avoid: At some point, the bottom bracket must be replaced. Because the inner bearing, also called bottom bracket, has the important task of guiding the bottom bracket shaft. An inner bearing is always composed of at least two bearings, which support the shaft on both sides of the bottom bracket shell. Radon also offers reliable tools in this particular area, especially for Press-Fit bottom bracket, but also for other standards.
Features - Pro assembly and disassembly tool set Press-Fit
- For the assembly of bearing shells or of Press-Fit bottom brackets
Product features
- For axle diameter: 24 mm
- Length: 240 mm
- Diameter: 21 mm
Compatibility
- Shimano Pressfit
- For mounting bearing shells or Press Fit bottom brackets (Press-Fit BB, BB30 and 24mm bearings)
- Suitable for bearing types BB30, BB86/92 and BB90
Material
- Tool steel
Weight
- approx. 242 g
Scope of delivery
- 1 x Pro assembly tool for Press-Fit bottom bracket
- 1 x Pro disassembly tool for Press-Fit bottom bracket
Radon Pro: professional equipment for the workshop
The tools of the Pro series were designed for demanding bicycle wrenches and mechanics. The special tool must meet special requirements in regular, multiple use in the bicycle workshop. High-quality raw materials, precise manufacturing techniques with low tolerances and careful quality assurance make Radon Pro tools reliable helpers for the bike. They convince through reliability, robustness and durability.
4059454033061
It does the job. The press tool is excellent but a bearing-cup extraction-stick is made from weak material. It is too expensive for what it is.
Works as expected
nickel merci BD
Super Set. Damit klappt die Reparatur ohne Probleme. Kann ich jedem nur empfehlen! Das Einpresswerkzeug macht wirklich Sinn, da es die Lagerschalen sauber führt und Verkanten ausschließt. Ich wollte zuerst ein selbst gebasteltes Tool verwenden, bereue den Kauf aber genau deshalb nicht.
The press works well, just that 1 side was not pressed in fully and the other was. However it was 100% straight so I just gave the drive side BB a few punches with the side of my plastic hammer and the 1-3mm of space where gone. Always look at both sides when doing this, to much torque can destroy the frame. The removal tool does it's job, I think it's useful to do 1 side with the tool and the other with a large flat screw driver and hammer because it's difficult to position the tool when 1 side it gone. They should add a ring you can put on there so when 1side is gone the tool still stays straight and you can hammer out the other side.
Mit dem Werkzeugset sollte ein Shimano SM-BB72-41B getauscht werden. Die 4 Zungen des Demontagewerkzeugs werden durch die Innenhülse soweit zusammengedrückt, dass die Enden nicht mehr sauber in die Lagerschale greifen. Ein geordnetes Austreiben der Lagerschalen ist so nicht möglich. Abhilfe schafft ein leichtes nach außen knicken der Zungenenden (ähnlich Parktool BBT-90.3). Die Ausführung der Druckscheiben beim Montagewerkzeug würde zu einer Einleitung der Presskräfte auf die Kunstoffhülse und im weiteren auf den Lagerinnenring führen. m.M nach kann dies zu einer Vorschädigung des Lagers führen. Abhilfe schufen zusätzliche Adapterscheiben die den Druck auf die Lagergehäuse einleiten. Fazit: Mit etwas Bastelei ein durchaus verwendbares Werkzeug. Wer dies scheut, sollte für Shimano Pressfit ein anderes Werkzeug wählen
Das Demontage-Werkzeug ist unbrauchbar, springt beim Ausschlagen des Press-Fit Innenlagers einfach über. Das Montage-Werkzeug hat dagegen einwandfrei funktioniert. Montage-Werkzeug: 5 Sterne, Demontage-Werkzeug: eigentlich 0 Sterne.
Hallo, hab heute das pressfit Demontage und Montage Werkzeug bekommen und gleich verwendet. Rechte Lagerschale war sehr fest und das Kugellager wurde von der Kunststoffschale beim Austreiben getrennt. Der Kunststoffkonus ließ sich dann leicht mit einem Holz austreiben. Die Einpressung des neuen Innenlagers funktionierte dann sehr gut.
It does the job. The press tool is excellent but a bearing-cup extraction-stick is made from weak material. It is too expensive for what it is.
Works as expected
nickel merci BD